3/9/2023 0 Comments Log file viewer![]() It came from the factory with version 6.10 firmware, and I've been loading version 5.10 projects into it because my FTView Studio is just version 6.10 (with RSLinx Enterprise and the Transfer Tool patched to support the new terminals). I happen to have a brand new "PV 6" 600 terminal, 2711P-T6C20D8 on my desk. You might see performance or storage limitations if you are trying to log tens or hundreds of thousands of entries. As I recall a 2048 entry alarm log was under 60 kb. The default is just 128 entries, but I run a PV 1250 application with 2048 entries with no trouble. The Alarm Log size is limited by the Alarm Setup -> Advanced -> History -> Size field. I'd have to dig up the technote or user manual citation.īut the Alarm Log files seem to copy without incident even if I just use the batch file to copy them from Internal Storage to the Removable Storage. In my experience, the Data Log files created and managed by the Data Log service need to be closed by the operating system before you can copy them off the terminal. Is no reset required as is with data log retrieval? If I understand what you're saying all I need to do is create a Notepad file with your 4 lines of text in it and save it as auto.bat, store it to a usb stick and plug it in to extract my alarm logs? With that in mind are there limits to alarm log files as well? ie 300k before they start writing over the oldest values. I am familiar with how to log data files and have done so in the past. Secondly, I am trying to log alarm files from my PV 600. I am trying to see if I understand this correctly. I used Windows Notepad to create a text file on the flash drive root directory named 'autorun.bat', which contains these four lines:įirstly, thank you for this info. Mine is an old Corsair Flash Voyager, 8 GB, formatted for FAT16 so that the PV can see it. ![]() I used a batch file on a USB thumbdrive to extract the log files from my PanelView. Use these copy statements with appropriately substituted Application names and Data Log Model names in your batch file.Ĭopy "\storage card\rockwell software\RSViewME\logs\YOUR_APP_NAME\DlgLog\YOUR_D LOG_MODEL_NAME\*.*" "\USB Storage\"Ĭopy "\windows\logs\Your APP Name\DlgLog\Your datalog model Name\*.*" "\USB Storage\" There's another Knowledgebase article, AID 35513 (TechConnect Required), that gives us the important information about the path to the *.LOG files, rather than the *.ALM files. If you have a model of PV that allows desktop access and FTP access to the file system, you might be able to do this over FTP as well I have not tried. You can do this with an CF card or SD card as well, depending on the type supported by your logic module. When the window closes, I remove the thumb drive. When I plug in the USB thumbdrive to the PanelView, the batch file runs and the 'Pocket CMD' window pops up in the foreground for a few seconds. Where 'Sandpounder_rev32' is the application name I'm running on the PV . ![]() I used Windows Notepad to create a text file on the flash drive root directory named 'autorun.bat', which contains these four offĮcho Copying Alarm Logs to USB Memory DeviceĬopy "\storage card\rockwell software\RSViewME\logs\Sandpounder_rev32\M_Alarms\ *.*" "\USB Storage\"Ĭopy "\Temp\~MER.00\M_Alarms\MachineAlarms.mal" "\USB Storage\" You can use a CF card or SD card as well. To get those files off the PanelView file system, I use a USB thumb drive. My terminals were a few years older than yours (PV 1000, running 5.10.03 firmware), and of course I'm looking for the *.ALM files rather than the *.LOG files. Get a current copy of that article the utility has recently revved up to 1.90 and the instructions have changed slightly. The Knowledgebase article you're probably looking at is AID # 33924, RSView Enterprise Log File Viewer () (Access Level: Everyone). I think you're asking about the Data Log files themselves, which are created by the Data Log Model for use by Trend objects. I have recently had very in-depth experience with PanelView Plus terminals and their Alarm Log files. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |